get started : bend it

Get Started

Getting started has never been easier. Select a category from the pull down or search for more information. This list is pulled from our Blog, Video, and Tips areas. Looking for products? Check out our Start-Up Kits.

Does using a wider foil on my project make it stronger?

Does using a wider foil on my project make it stronger? Does using a wider foil on my project make it stronger? Your project may be a little bit stronger with a wider foil since a wider solder line will tend to keep a seam from bending or flexing more than a narrower one. However, its not enough of a difference to be a major consideration in choosing a foil width for your project. The more likely reasons for choosing one foil width over another are as a design feature. You may want wider or narrower solder lines in certain areas of your project. to account for thicker or thinner glass. Youll need to choose an appropriate width of foil to have your solder line remain a consistent width. If you think strength or structure is a problem, some reinforcing other than just a wider foil is going to be necessary. For minor reinforcing, ask your supplier for a reinforcing strip.

Oh, My Aching Back and What You Can Do About It

Oh, My Aching Back and What You Can Do About It Youve spent the last several days in a flurry of activity getting ready for the show. Reaching, lifting, bending, packing, shoving, sitting for hours during travel, standing in awkward positions while unpacking, setting up your booth, walking back and forth on uneven ground. Perhaps youve even been subjected to extreme temperature changeswind, rain, drafts. In any case, youre finally done. Youve certainly earned a few moments of relaxation, so you reach for a cool (or hot) drink, plop yourself down in a foldout or canvas chair, slump back, stretch out your legs, and survey the efforts of your labors. Now its time to get up and greet a prospective buyer. But you cant move. Pain shoots through your back, your legs and your shoulders. You look and feel like a chick trying to peck its way out of an egg as you struggle to get up and out of your

Easy Glass Picture Frames for Mom and Dad

Easy Glass Picture Frames for Mom and Dad Delphi associates are raving about the new Bend It Molds from Creative Paradise. The clever design makes it easy to fuse projects that stand up on their own, and the mold comes in three different sizes, Large, Medium and Small (or Baby Bend It.) The picture frame for mom (top left) was made by glass artist Denise Christmas-Gibson using the Medium Bend It Mold. The Fathers Day golf project (at right) was also created by Denise using the Large Bend It Mold. What would you make with this mold?

Celebrating Innovations in Art Glass

Celebrating Innovations in Art Glass Delphis 40th Year Anniversary is quickly approaching, which will be commemorated with the release of the 2012 Annual Catalog.Our constant commitment to making art glass accessible to everyone by providing the largest selection of supplies and art glass has truly made us innovators. One of the ways we stay on the cutting edge is to bring tools and products that enable the process of creating to become enjoyable and rewarding for everyone. This month we are featuring two of our vendors whose products support the mission of Delphi and embody innovation. We recently caught up with the President of Creators Stained Glass, Inc. and Inventor of the Cutters Mate, CirclePro and Strip Pro, Ray Nicholas. He told us the story of what sparked his creation of these tools.He began creating stained glass in 1992.His services become so in demand that by 1996 he had developed the Cutters Mate to

Janet Schrader

Janet Schrader In 1979, a journey began. Thats the year Janet Schrader began working with glass, and she was immediately hooked. Color is a very important part of who I am, so finding all the properties of changing color in glass has held my interest for many years. I love how glass changes color depending not only on the light source but also that it changes from morning to night as the light quality changes. Around 1988, Janet encountered dichroic glass for the first time, and fusing became the new focus of her glass art launching her successful line of handmade jewelry which she sold nation-wide. Janets one-of-a-kind stained glass, jewelry and fused art have been met with enthusiasm, and winning awards including 1st and 2nd prize in the professional artist category for Fusion/Cast/Kiln work at the 2012 Glass Craft and Bead Expo in Las Vegas.

How to Make Your Own Blown Glass Ornaments

How to Make Your Own Blown Glass Ornaments GLASKOLBEN cylinders are pre-blown clear glass cylinders with blow pipe ends, used for blowing glass balls. Glaskolben cylinders are used throughout Europe for making Christmas tree ornaments. Glaskolben is a German word that translates to glass bulb. WATCHAVIDEOONBLOWINGGLASKOLBENORNAMENTS. SUPPLIES/EQUIPMENT Torch head for Mapp Gas use Gas/oxygen torch Glaskolben™ cylinder 90 COE frits and powders for decoration Ornament cap and loop set (available in gold or silver) COMPATIBILITY Glaskolben is compatible with Uroboros and Bullseye 90 COE glass frit and powders. Do not use any other COE as it may cause stress or fracture. HOWTOBLOWANORNAMENT 1. Light the torch and adjust the flame - a broader flame is better. Select a Sealed End Cylinder Glaskolben™ and introduce it into the back of the flame away from the torch. Rotate it as it is brought into the hotter area of the flame. Continue to rotate until the cylinder is glowing

Donna Sarafis: Basics of Fusing Part 2

Donna Sarafis: Basics of Fusing Part 2 Part 2 of a 2 part series on the basics of glass fusing. In this weeks article Donna gives advice on indispensable tools for beginner glass fusers. In the beginning, I used one larger tool, and that was a Super Star Grinder. It is still running, running, running. Others have come, and some have gone, but this one is still here. For smaller cold working projects, diamond hand pads do a nice job. The next cutting tool that I bought was a saw. My Taurus 3 Ring Saw has worked extremely well for me, and I love what I can do with it that I couldnt do before, but I worked for 2 years before I purchased this nifty item. As for cutters and breakers, I have many, but for me, the Silberschnitt breaker pliers are a must for small (1/4) strip breaking.....saves so much glass. I use both

Setting Up Your Stained Glass Workshop

Setting Up Your Stained Glass Workshop I am about to set up my new workshop. I was just wondering what you think are the most important things to include? Since every situation is different, we cant give you specific answers, but here are some things that you should give some thought to. We think that the two most important things in a workshop are safety and comfort. You obviously want everything in your workshop to be as safe as possible. Ideally, you will want to have proper ventilation, plenty of lighting, safe storage areas for glass and chemicals (do you have children?), grounded electrical connections, no extension cords, safe disposal for glass and supplies (trash cans as opposed to plastic bags), and easy to clean surfaces (no carpet on the floor). Comfort is the next most important consideration. The height of your work surface is very important. If you arent comfortable, you wont be able to

Bedazzled Earrings: A Microwave Fusing Project

Bedazzled Earrings: A Microwave Fusing Project By Rita Levine Skill Level 2 (Adult 1-5 1 being the easiest, 5 being most difficult) Time to Complete 45 Minutes Materials Fuseworks Kiln Fuseworks Kiln Paper Fuseworks Glass Cutter Wheeled Glass Nippers Ruler Westrim pearl assortment Sterling Silver Plated Square Cabochon Mini Links - Delphi 85435 2 hat pins Earring wires Scrap fusing glass 90 COE Chain-nose pliers Round-nose pliers Instructions 1. Place white glass on a clean flat cutting surface with the smooth side of the glass facing towards you. 2. Start on an edge of the glass holding the cutter firmly in one hand. Keep the cutter perpendicular to the glass. Push the cutter gently and evenly across the glass. Decrease pressure slightly as you reach the opposite edge of the glass; lift the cutter off the glass at the end. 3. Breaking the score line can be done with breaking pliers. Hold the glass in