get started : clear glass

Get Started

Getting started has never been easier. Select a category from the pull down or search for more information. This list is pulled from our Blog, Video, and Tips areas. Looking for products? Check out our Start-Up Kits.

How to Create Blown Glass Ornaments | Delphi Glass

How to Create Blown Glass Ornaments | Delphi Glass Learn how to create beautiful glass ornaments with Glaskolben pre-blown clear glass cylinders with blow pipe ends. Delphi Artist Val Oswalt-De Waard demonstrates how Glaskolben may be blown freehand into a ball using a Hot Head torch and MAPP gas, eliminating the time-consuming method of pulling points from glass tubes.

Combining Fabric or Paper with Your Glass

Combining Fabric or Paper with Your Glass Did you know that you can sandwich fabric (or paper) between glass just like you do with pressed flowers? It sure opens up a lot of possibilities for creating one-of-a-kind projects. Heres how 1 Cut two pieces of thin clear glass (ideally, single strength or thinner) to match your pattern piece. Dull the edges of each piece, if necessary, with a fine grinder bit or scythe stone. 2 Carefully clean the surfaces of these pieces that will be on the inside of the sandwich. Once you have sandwiched the fabric inside the glass, you wont be able to clean the glass again. 3 Cut a piece of fabric to match the glass pieces you cut. 4 To create your sandwich, place the fabric on the bottom piece of glass (clean side up). Add the top piece of glass (clean side down). Now hold your sandwich together with a couple of

How to Know When You Should Cap Dichroic Glass | Delphi Glass

How to Know When You Should Cap Dichroic Glass | Delphi Glass http /nAWvrk DelphiGlass.com offers glass and supplies for fusing and jewelry crafts. See the fuse bar featured in this video at http //www.delphiglass.com/dichroic-90-coe/dichroic-packs-90-coe/cbs-fuse-bar?source=sm

Holding Small Pieces In Place While You Solder

Holding Small Pieces In Place While You Solder 1. Make sure that your pieces are clean and dry. Cut a piece of clear contact paper, remove the backing and lay it sticky-side-up over the pattern. 2. This is a perfect way to hold cut glass, globs, jewels, or marbles in place for tack soldering. As you can see in the photo, you can even move the sheet around and, if you are careful, you shouldn’t disturb the glass at all. 3. Tack solder the pieces to each other as you normally would. Then, remove the contact paper and finish soldering the front before turning the project over and soldering the back. Reprinted with permission from Stained Glass News. All rights reserved.

KraftyBlok Project Ideas and Inspiration

KraftyBlok Project Ideas and Inspiration Watch this video to give you ideas on how to use your Kraftyblok. A pre-drilled glass block, its easy to add lights or other decoration inside. The smooth, clear glass surface makes it easy to mosaics, painting, etching or other decorative effects. Made by Diamond Tech Crafts. http //www.delphiglass.com/more-crafts/glass-blocks/ To see all the Krafyblok products currently offered by Delphi Glass please follow this link http //www.delphiglass.com/more-crafts/glass-blocks/?sort=ref01up&source=sm

Is My Piece of Glass Cracked?

Is My Piece of Glass Cracked? How can I tell if a piece of glass is cracked? Did you ever notice the workers in your local glass shop tapping on a sheet of glass before they move it? They do that to see if it has any cracks. Cracked glass has a very different sound when tapped than intact glass does. This will be the best way to tell if your glass is broken. However, you should try it out on some other sheets before you try it on a piece that you think may be broken. Once you have heard a cracked piece, you will know what it sounds like. Hold the sheet from the top edge with one hand. Hold it out and away from your feet, just in case. Gently tap the sheet with one of your knuckles. A solid sheet of glass with no cracks will have a solid, clear ringing sound.

Beginner's Notes: Making Glass Feathers

Beginner's Notes: Making Glass Feathers The Feathers of the Phoenix Plate is the most complex plate I have made so far.Making the glass feathers and fusing the plate is an 8-step process. It starts with a glass brick that is fused from layers of transparent and opal glass dammed between four kiln bricks. The brick is then sawed in half and bookended, then fused again. After fusing, the brick is sawed into thin slices with a round diamond bladed Taurus 3 glass saw. The slices are again bookended together and fused with a piece of clear glass on top. All the glass feathers turn out beautifully and never look the same. They can be used in jewelry and plates. The feathers are laid out on a black piece of opal glass and fused flat. Then a transparent piece of glass is placed on top, and the plate undergoes another 12-hour fusing. The last step

Fused Stained Glass Pendant

Fused Stained Glass Pendant Sometimes necessity is the mother of invention, and sometimes invention comes when you have nothing to lose. Early in my career, I had three metal-clay-and-fused-glass pendants fail in a single day. The glass cabochons simply shattered and fell away from the silver after the pieces were fired because I had neglected to cut an expansion hole underneath the cabochons. Augghh. Lesson learned. But now I was left with three ugly pieces of silver, each with small pieces of glass permanently fused into bizarre locations on the surfacea loss I could not afford. Weeks later, after tryingunsuccessfully to remove the glass, I decided to try fusing glass in patterns onto the surface of the pendants. The results were surprising, and the Stained Glass process was born This technique begins with any fired metal clay with a flat surface. Small shards of fusible glass are then attached to the silver. After

Glass Fusing Q&A

Glass Fusing Q&A No oneknowstheexactorigins of glass fusing although there is evidence that the Egyptians were familiar withrudimentary techniques. The Romans however arenoted by scholars for developingrefined glass fusing skills. Although technology has changed the way modern glass fuserswork,the technique isessentially the same as those developed by the Romans centuries ago. The basic technique involvesstacking two or morelayers of fusible glass, which are then placed in a kiln and gradually heated to between 1450-1500 Fahrenheit.At these temperatures the layers of glass fuse, or melt together and become one. Unfortunately, glass kilnsare large andexpensive,whichkeeps most Hobbyists from pursuing this art form. Now there are new kiln options, including theThe Fuseworks Microwave Kiln. This device works in most household microwaves and can fuse glass in about 3 minutes. Here are some common questions we get on fusing in this modern-day kiln. The following are Q A complied by Diamond Tech, the manufacturer of Fuseworks

Turning Photos into Glass Projects

Turning Photos into Glass Projects My husband and I recently met a spectacular couple, a genuine cowgirl and cowboy. Besides being fortunate enough to purchase a very sweet horse from them, we are proud to be able to call them our friends. While at their home I learned that her one of her best friends, her horse, had passed away the previous year. Yoda had carried her though years on the Rainbow Riders drill flag team, taken her to reigning championships, and safety along countless miles of trails. I wanted to do something special for her, and also try something new for me. I remembered seeing an article in the Delphi newsletter about making fused glass silhouettes from a photograph. While at her home I snuck a picture of her and Yoda sliding to victory, on my cell phone. I downloaded the picture and adjusted it to an appropriate size for a 10 by 10

Creating Wellness through Glass Art

Creating Wellness through Glass Art Photo credit Green Earth Glass We all know that making something beautiful feels good, but did you know that there are health perks too? It’s true. The creative process of planning your projects while overcoming the obstacles you face when bringing your glass art ideas to life is stimulating for the brain on so many levels. While it may be challenging to try a new technique or even a new form of glass art, the entire process is actually more relaxing for your brain than you think, all the while stimulating it for growth. The end result is a gorgeous piece of glass art and a refreshed mind. You really need to do this for yourself to bring more peace and harmony into your world. At Delphi Glass, we completely agree with this which is why we offer our classes year-round. Sign up for one of them to

Stained Glass News Feb. 2013 Edition- See What's New

Stained Glass News Feb. 2013 Edition- See What's New Heres our list of 5 Favorite New Items from the February 2013 edition of Stained Glass News. 1. Snowflake Casting Molds from Colour de Verre With the new premium mold from Colour de Verre you can make incredibly detailed, beautiful snowflakes. There are so many ways you can use these snowflakes. Hang them on their own (they are light) or incorporate them into projects. Were excited about how creative you can get making the snowflakes depending on the size of frit and firing temperature. LOVE them with dichroic. Check out the mold and free project sheets posted on our website. You wont believe the gallery quality of the pieces you can create. 2. Barefoot Tools are Back and Better Than Ever. Powder Vibe Electric Mandrel Spinner The Bearfoot Tools line has some of our customers favorite tool; and

Friendship Bracelets using Fused Glass Nano Beads

Friendship Bracelets using Fused Glass Nano Beads Did you know that Friendship Day and Sister Day are both on the first Sunday in August? Want to do something special for a couple of those special friends or family members in your life. How about making a friendship bracelet that you and your friends will love and cherish for years to come? Each person will get the same or similar bracelet, signifying the unity of people represented. This special friendship bracelet uses fusible glass to create beautiful lifesaver candy beads from glass frit. Supplies youll need System96 Medium Frit - Clear, plus any other transparent or opaque colors you might like Nano Beads casting mold Heres how to make your bracelets 1. Select a colored frit to represent each friend or family member(dont forget yourself) - the number of colors represents how many lifesaver beads youll make per color. For example, 5 people = 5colors of frit,

How to Make Your Own Blown Glass Ornaments

How to Make Your Own Blown Glass Ornaments GLASKOLBEN cylinders are pre-blown clear glass cylinders with blow pipe ends, used for blowing glass balls. Glaskolben cylinders are used throughout Europe for making Christmas tree ornaments. Glaskolben is a German word that translates to glass bulb. WATCHAVIDEOONBLOWINGGLASKOLBENORNAMENTS. SUPPLIES/EQUIPMENT Torch head for Mapp Gas use Gas/oxygen torch Glaskolben™ cylinder 90 COE frits and powders for decoration Ornament cap and loop set (available in gold or silver) COMPATIBILITY Glaskolben is compatible with Uroboros and Bullseye 90 COE glass frit and powders. Do not use any other COE as it may cause stress or fracture. HOWTOBLOWANORNAMENT 1. Light the torch and adjust the flame - a broader flame is better. Select a Sealed End Cylinder Glaskolben™ and introduce it into the back of the flame away from the torch. Rotate it as it is brought into the hotter area of the flame. Continue to rotate until the cylinder is glowing

How to: Create Faux Opals with Glass

How to: Create Faux Opals with Glass Before I was fortunate enough to own a kiln, I used to experiment with all kinds of polymer clay using recipes for faux gemstones. It was fun and inexpensive. While giving a fused glass lesson the other day, I said, Hey, lets try to make some faux opals. So, we crushed up some green and orange, clear backed dichroic glass (from the Uroboros Magic Box), and mixed in a tiny bit of crushed opaque white glass. We cut two transparent ovals, covered them with Bullseye Glastac Firing Glue, and sprinkled on the frit. We added another layer of glue and piled up some more frit. The beauty of this glue is that you can use as much as you want. I love it for holding the frit on the edges of bowls and glass. The fired pieces looked like opal cabochons. To make the cabochons more opaque, I used my

Stained Glass News 25th Anniversary Contest

Stained Glass News 25th Anniversary Contest Check out these Project Ideas Now for some news from Stained Glass News SGN, in conjunction with Aanraku Glass Studios and Spectrum Glass, has announced details of their their 25th Anniversary Contest. Nine winners will be chosen to receive cash prizes as well as glass and supplies from Spectrum Glass Studios. To enter the contest make one of three new Aanraku projects using Spectrum Glass - either art glass or System96 - and send a photo of your work to Stained Glass News in Newaygo, MI. You can use any glass crafting technique and enter as many projects as you like. Buy your supplies from Delphi Glass or your favorite local glass retailer, then visit stainedglassnews.com/contest for complete rules and entry form. You have until December 31st to mail in your project. Winners will be announced in the March 2013 issue of Stained Glass News. Project Categories Cash

Simple Solutions to Glass Art Pet Peeves

Simple Solutions to Glass Art Pet Peeves Here at Delphi, we love a good reason to celebrate. With the Holiday Season still looming weeks away, we were feeling anxious for a bit of excitement now. The good news? There are lots of lesser known holidays scattered throughout the year if you only look for them. (September includes a favorite of ours; National Talk Like a Pirate Day.) We needed another zany mood boost to get us through Thats how we found this gem Its National Pet Peeve Week. In honor of this holiday we thought long and hard about what really gets under our skin and pushes our buttons while working on projects. Check out our top glass art pet peeves, and the simple solutions sure to put a smile back on your face. Pet Peeve Disappearing Marker Lines Solution Mark Stay II saves the day. Just wipe

6 Tips for Decorating Your Thanksgiving Table with Glass

6 Tips for Decorating Your Thanksgiving Table with Glass Show off your art glass creations. Here are 6 easy and inexpensive ways to incorporate art glass into your Thanksgiving dinner table dcor. 1. Glass bottles are easy and inexpensive to use. Cut the bottoms of glass bottles of varying heights. Place over votive candles, and decorate with etching, twine, ribbon and other found objects. Download instructions on how to make the centerpiece pictured top right. I also love these amber-colored bottle hurricanes I found onEtsy (at right). They provide just the right amount of romantic ambiance for the dinner table. 2. Decorate pillar candles with glass frit for extra sparkle. In browing for Thanksgiving inspiration online, I ran across this great idea by HGTV to roll pillar candles in lentils for a unique table decoration. Then I thought, why not roll them in glass frit. The frit

Is It Safe to Use Fused Glass for Dinnerware?

Is It Safe to Use Fused Glass for Dinnerware? The official answer from the glass manufacturers is, All tested compatible glasses have been tested by the FDA for food bearing surfaces and were determined to be suitable.However, if you add other processes or compounds to the items, for example paint, stains, decals, glazes, etc. it is important to check that these items are also approved for food bearing surfaces. In addition it is of the utmost importance that dinnerware items be properly annealed, especially if youre going to place hot food on them - the thermal shock could cause a break in poorly annealed items. This Randys ProTip brought to you from the book Introduction to Glass Fusing by Petra Kaiser. VisitWardell Publications. Also, at Delphi we take food safety and dinnerware very seriously. We always recommend that certain glasses are capped with clear. These are usually irids, dichro and glass with texture, since these can also trap

Stained Glass News Nov. 2012 Edition- See What's New

Stained Glass News Nov. 2012 Edition- See What's New Heres our list of 5 Favorite New Items from the November 2012 edition of Stained Glass News. 1. Realistic Leaf Casting Molds from Colour de Verre We always flip for the latest new molds from Colour de Verre, and these premium leaf molds are fantastic. They allow you to make gallery quality, detailed glass art pieces. You can create with Kiwi, Rain Forest, and Aralia leaf molds. Check out the molds and free project sheets posted on our website. You wont believe what you can create. Kiwi Mold Rain Forest Mold Aralia Mold FREE Kiwi Project Sheet FREE Rain Forest Project Sheet FREE Aralia Project Sheet 2. Our Favorite New Glass is Making us Twizzle. CBS Dichroics newest pattern, Twizzle, features a fun zig-zag

How to Make a Suncatcher Ornament with Scrap Glass

How to Make a Suncatcher Ornament with Scrap Glass As a crafty person, the holiday time can be rough. Not only are we lugging around 7.4 million pounds of product to various craft shows, we also have the expectation upon us that we will hand make everyones holiday gift...because, were crafty like that (plus, you and I both know that it would KILL us to buy gifts that we could otherwise make - its in our DNA). So, at the end of the day - our backs and feet are killing us, wed rather die than smile or make small talk with one more person, we have a car full of stuff to unload (which we also both know will stay there for another 3 weeks until we cant stand it much longer)...and I have to MAKE a present for your sisters husbands aunts niece who is in college? Oy. Enter the scrap glass suncatcher slash holiday ornament. This

How to: Make a Scrap Metal Pendant

How to: Make a Scrap Metal Pendant I am always trying to save my scraps, even if they are metal. I grind my glass, pin backs and bails with my dremel tool (Ive found that they stay glued together much better that way), and I started saving all of the grinding scraps. I save the sterling silver grindings in one bottle, and my gold plate with mixed metals, in another. One day, I was looking at some old green sea glass lying on the beach. I thought about folks sending notes out in a bottle, and it being found miles away, full of sand on a beach. I wondered if I could capture that idea in a pendant. When I got home I put those ground metals to use. First, I cut one square of transparent glass, then a smaller square of aqua-green transparent glass, and a tiny square of transparent glass. I sprinkled some of the

Household Items You Can Use As Tools

Household Items You Can Use As Tools From our Facebook fans, here are a few household items that can be used as tools in art glass creation. Some great ideas here. Hairspray for gluing (the non-aerosol kind, the cheaper, the better. ) Olive oil for your glass cutter The spoony straw from a slush puppie for pouring small amounts of frit Butter knives for bead making Chinese take out containers for storing smaller pieces of fusable glass. They are rectangular and stack well with a clear lid. Also, the soup containers to store frit (each size of frit in its own container stacked within the others of like color and only the top one needs a lid, and they are clear) Glass yogurt pots for storing frit and other bits Plastic containers that tubs of crystal light comes in for storing smaller pieces of glass. I also save the tubs for mixing glue/water, frit and water, paint,

Your Dichroic Questions Answered

Your Dichroic Questions Answered What is dichroic glass? Dichroic glass is regular glass, dressed up. It gets its sparkling metallic colors from a complex scientific process. Glass is placed in a special vacuum chamber, in which quartz crystal and metal oxides are then vaporized. The resulting mist settles onto the glass and forms a unique crystal structure that reflects and transmits light in amazing ways. Coatings by Sandberg put together this great video illustrating the dichroic process. Where did dichroic glass come from? Dichroic glass dates back to 4th century AD, but was more recently used by NASA for dichroic filters. Dichroic glass was discovered in the 1970s by the art glass community and is now a coveted design element due to its unique characteristics. Why does dichroic glass change color? The coatings applied to the surface of the glass create both transmitted color (which is seen when you look through the glass) and

See Things from a New Perspective with Kaleidoscopes

See Things from a New Perspective with Kaleidoscopes Kaleidoscopes are a fun tool to use to enjoy optical illusions. With some mirrors, glass and colorful tidbits, you can create your own kaleidoscope that takes you to a world of beautiful images thanks to the items inside of it rotating along with the light coming in from the opposite end. The result is magical and can awe both children and adults. Glass kaleidoscopes are particularly beautiful. They often look impressive on the outside as well. Magic on the inside and out, glass kaleidoscopes are an ideal summer stained glass project. Here’s how to make one of your own. In addition to all your glass cutting tools, you’ll need clear glass colored glass in the colors of your choosing copper foil brass rod solder (to use in your soldering iron) flux mirror kit disc kit faceted beads decorative copper or brass elements for adornments and leg supports patina solution felt

Clayton Stang: Out of the Shadows

Clayton Stang: Out of the Shadows We first noticed the work of Clayton Stang in Delphi's Artist Gallery. His glass shadowbox "Night Owl" received many comments in our gallery and on Facebook. Artists were asking, "how did he do that?" We tracked him down for a short Q&A. How did you get started in glass? I was the baker at an adult summer camp 13 years ago. They were offering stained glass classes. I took to it immediately. Two years later, I became the stained glass instructor at the camp. Why glass? I was a color stylist in animation for years, so the colors of glass called out to me. Sometimes I just go into the glass store and look at glass for the thrill of it. Ive always loved stained glass. I just had to wait until I grew up and could afford it. How have your other interests/hobbies/career influenced your

Exciting New Products from Uroboros

Exciting New Products from Uroboros We are thrilled to share with you the Winter 2012 new products from Uroboros Glass. Each of these new products is based on Uroboros unique manufacturing strengths, while adding depth to their most popular product groups. Streamer Bits Glass (all offered in 90 and 96 COE) White Streamer Bits on Clear Cobalt Blue Streamer Bits on Clear Red Opal Streamer Bits on Clear Noodles and Stringers Sprinkles (offered in 90 and 96 COE) Glass Noodle Bits, Mardi Gras (offered in 90 and 96 COE) Noodles and Stringer, Mardi Gras (offered in 90 and 96 COE) Cobalt Blue Opal (offered in 90 COE) Pastel Green Opal Noodles (offered in 96 COE) Pastel Green Opal Stringer (offered in 96 COE) Frit Celadon Opal is now available in all grain and package sizes (offered in 96 COE) View these and other NEW fusible glass products here.

Making Thanksgiving Memories

Making Thanksgiving Memories One of my favorite memories growing up in Northern Wisconsin was our annual family Thanksgiving Day dinner. With lingering aromas from the kitchen, waiting to see cousins that I hadnt seen for several months, and the anticipation of who breaks the wishbone, the day seemed magical. Each year it seemed we created new family traditions, and our Delphi Family would like to suggest some traditions your family can start 1. For a fun accent piece for the holiday table, try slumping brown or green bottles as a side dish. The size is perfect to serve Aunt Mildreds sweet potato hash or your family favorite. The color will add punch to the table as well. 2. Make it easy to identify whos drink is whos. We like the idea of creating glass beads strung with silver wire and attached to the goblet stem to claim your stake. As a take