Shop By Category
Final Hours - Save on the Taurus 3 and Max 10
community : product reviews
 
Product Reviews
1
...
480
481
482
...
605
Grinder Cookie by irish_lasse on August 12, 2011 5 stars
Pros
Really like using this tool, it's perfect for my hand size and saves my fingers from cramping when holding a small piece of glass!
Cons
Other Thoughts

Grinder Cookie by Kenzartwork on August 10, 2011 5 stars
Pros
This actually works very well. Works well for grinding small items. I do feathers with long sharp points. This works great for pieces like that. Less breakage on the sharp tips with this. Ordering two more!
Cons
None
Other Thoughts

Oceanside Gold Iridized Black Hand-Rolled Opal - 96 COE by charz36 on August 9, 2011 4 stars
Pros
Very pretty glass
Cons
changes color with firing at 1350 hold 5 you get a very nice gold, better than the unfired glass, at 1465 hold 0 you get blue and purple splotches that are attractive above that temperature you probably will get all purple.
Other Thoughts
Test first

Handy Hangers - 5 Pair by SteveK on August 9, 2011 5 stars
Pros
I use these all the time and have never had any problems. I do clean them well before tinning.
Cons
none
Other Thoughts
I always buff them clean and shiny before tinning, which helps a lot.

Frit Sifter by belmore on August 5, 2011 5 stars
Pros
Thought they were rather expensive at first, but they are really well made and super easy. Heat your glass, quench in cold water, smash a bit, and then stack your sifters - smallest on the bottom and graduate to the largest on top. Shake your frit down in size, and it's done!
Cons
The whole process is a bit time consuming, but it does save you money in the long run.
Other Thoughts
No waste of your glass. Only sifters I've seen that will give you real powder.

Morton Glass Caddy by Sandra F on August 1, 2011 5 stars
Pros
This is a very handy item. It is so nice to be able to store glass and tell in minutes what colors and kinds of glass you have. Would recommend it.
Cons
None
Other Thoughts

PMC3 Syringe by SilvArtGlsJwlry (top contributor) on July 30, 2011 5 stars
Pros
Draw with silver using the syringe- you can create your design right on the glass, affix CZs, silver casting beads, or create a filigree base or design.
Cons
None!
Other Thoughts
Store your open PMC Syringe in a florist's vial (like for a corsage) filled with water to keep it good for months. Push the syringe into the vial so the entire tip is enclosed, and you don't have to worry about refilling a cup, or evaporation.

Generation Green (g2) Bottle Cutter by SilvArtGlsJwlry (top contributor) on July 30, 2011 4 stars
Pros
I really like my Generation Green bottle cutter. I cut bottles to make bowls, bells, candle holders, etc. I get consistently even cuts, can adjust the height and width as needed, and get good results.
Cons
Do not separate the bottles using water baths as the directions say. It does not work properly that way- the bottles split unevenly. If you use a candle flame you can direct the break properly. Heat the entire score mark first, then concentrate on one inch at a time, directing the flame where you want the glass to break.
Other Thoughts

Pocket Drill Set by SilvArtGlsJwlry (top contributor) on July 30, 2011 5 stars
Pros
This is great for times when you don't need or can't take a Dremel. I used it to drill pearls for a rosary. It works well, is easy to use, and is self-contained.
Cons
None. It does what it is designed to do.
Other Thoughts

Abrasive Stone by SilvArtGlsJwlry (top contributor) on July 30, 2011 5 stars
Pros
Great for filing down burs or smoothing rough edges on paperweights or recycled glass. Cheap option over sanding pads. Good for rough work.
Cons
Can't reach small areas.
Other Thoughts
It would be nice to see a smaller version of this.

Diamond Hand Pad Assortment - 4 Pack by SilvArtGlsJwlry (top contributor) on July 30, 2011 4 stars
Pros
Nice assortment of grits. They do a good job of removing burs on fused glass, or finishing edges of cut bottles. If you flip them over, the colored part is good for buffing off mild to moderate kiln dust on projects.
Cons
Many times I wish they were flexible. You cannot reach small areas at all.
Other Thoughts
They are a good deal for the money, and very useful.

17" Votive Bottle Hanger by SilvArtGlsJwlry (top contributor) on July 29, 2011 5 stars
Pros
Strong wire, good height. Easy to use. Candle and glass holder included
Cons
None
Other Thoughts
It would be nice to see a shorter version. The length of wire coming out of a typical bottle neck is great if you wish to hang it directly on a porch hook, but not great if you plan to make your own decorative hanger.

1
...
480
481
482
...
605