Making 3D flowers is a great way to use up your scrap glass. I arranged the flowers and created support using wire that I twisted with the Morton wire twister and brazing rods.
@pmeewes I believe this lovely arrangement was an original artwork by the artist that shared the photo. Looking at the scale of the flower being assembled on a grid surface in the additional image, I would estimate that the flowers each vary from about 2-1/4" to 4-1/2" diameter; making this full floral arrangement likely about 20" - 24" in full width. It certainly is a colorful and beautiful project!
@cathy p. Thank you. No, I did not have a pattern although I did have an original piece to look at. I worked on this piece off and on for a couple of months. I started with making the individual flowers, which went fairly quickly. The time consuming part came when trying to figure out how to put it all together. I thought at first that I could position the flowers first and then fill in with greenery and jewels. Had to take some apart when I realized that some of the greenery had to be soldered first, otherwise I couldn't reach it with iron. Thanks again for the compliments--it's my favorite of all that I have done, the colors are cheery and it brings a smile to my face every time I walk past it!
@Mrs1919 Thank you, I'm glad you enjoy it. I did not have a pattern. My mother inherited a similiar piece and I fell in love with it. I couldn't find any patterns for this type work so she let me borrow it to look at and study. Reinforcing the flowers was a trial and error experience. I started out with 3 main supports consisting of 3 or 4 pieces of 14 guage wire twisted together, running up from the bottom of the vase, the middle one ended with the blue flower. I added different branches off of these 3. When I first thought I was finished, I stood it up and the two sides seemed like they were waving! I then went back and added more support using brazing rods to tie together the three main supports in different places. I learned a lot while making this piece that I will incorporate into the 2 new pieces that I am making for gifts. Thanks again for looking.
comments4
Tuesday, August 28, 201891 Posts
@pmeewes I believe this lovely arrangement was an original artwork by the artist that shared the photo. Looking at the scale of the flower being assembled on a grid surface in the additional image, I would estimate that the flowers each vary from about 2-1/4" to 4-1/2" diameter; making this full floral arrangement likely about 20" - 24" in full width. It certainly is a colorful and beautiful project!
pmeewes
Saturday, August 25, 20181 Post
This is beautiful! Can you tell me what the finished size was?
giftinghouse
Wednesday, October 28, 20151 Post
Do you have a pi of the back side? I'd like to see the set-up, if possible. This piece is gorgeous and inspiring.
smarohl
Wednesday, September 7, 20111 Post
Very unique piece. Love it!!!
cjorth
Wednesday, March 30, 20112 Posts
@cathy p. Thank you. No, I did not have a pattern although I did have an original piece to look at. I worked on this piece off and on for a couple of months. I started with making the individual flowers, which went fairly quickly. The time consuming part came when trying to figure out how to put it all together. I thought at first that I could position the flowers first and then fill in with greenery and jewels. Had to take some apart when I realized that some of the greenery had to be soldered first, otherwise I couldn't reach it with iron. Thanks again for the compliments--it's my favorite of all that I have done, the colors are cheery and it brings a smile to my face every time I walk past it!
cjorth
Wednesday, March 30, 20112 Posts
@Mrs1919 Thank you, I'm glad you enjoy it. I did not have a pattern. My mother inherited a similiar piece and I fell in love with it. I couldn't find any patterns for this type work so she let me borrow it to look at and study. Reinforcing the flowers was a trial and error experience. I started out with 3 main supports consisting of 3 or 4 pieces of 14 guage wire twisted together, running up from the bottom of the vase, the middle one ended with the blue flower. I added different branches off of these 3. When I first thought I was finished, I stood it up and the two sides seemed like they were waving! I then went back and added more support using brazing rods to tie together the three main supports in different places. I learned a lot while making this piece that I will incorporate into the 2 new pieces that I am making for gifts. Thanks again for looking.
Mrs1919
Wednesday, March 30, 20113 Posts
Absolutely Goreous-- Would love to have pattern and exactly how did you reinforce the flowers? What an inspiration!!!
cathy p.
Thursday, March 10, 20115 Posts
How long did that take you? and did you have a pattern? it is Beautiful! I love it!
cathy p.
Thursday, March 10, 20115 Posts
Beautiful!
Report Abuse
Are you sure you want to report this comment?
Add a comment